Artikelnr. DC8060
Boost Converter 8-60V to 12-80V 12A 600W
Output Power: >500W
DC/DC Converters
Size: 76mm(L) * 60mm(W) * 56mm(H)
- Input Voltage: DC 8-60V
- Output Current: 12A Max
- Output Voltage: DC 12-80V
- Weight: 250
Input Current: 16A (MAX)
- Output Current: 12A MAX
Features:
- 600W high power boost module
- Input voltage :12-60V or 8-16V Selectable
- Wide output voltage (12-80V) adjustable
- Output current (0.1-12A) Adjustable
- High efficiency
- Ultra-low dropout voltage
Module parameters:
- Module Properties: non-isolated step-up module (BOOST)
- Input voltage: two input voltage ranges selectable (selectable with jumper on board)
1)8-16V input ( In this input mode,please do not over-voltage input, otherwise it will burn module)
2)12-60V input(default) - Input Current : 16A (MAX) Please enhance heat dissipation when current over than 10A
- Static Current : 15mA (12V to 20V. The output voltage increase, the static current will increase a little)
- Output voltage: 12-80V (continuously adjustable) ( the default output about 19V )
- Output Current : 12A MAX, if over 10A please enhance heat dissipation ( the higher the dropout voltage, the smaller the current )
- Constant current range :0.1-12A
- Output power : = input voltage * 10A, such as: input 12V * 10A = 120W, input 24V * 10A = 240W, Input 36V * 10A = 360W, input 48V * 10A = 480W, input 60V * 10A = 600W. If you need more high-power, two modules can be used in parallel , for example if you need 15A output, then connect two modules in parallel ,?the current of each module set to 8A then is OK.
- Operating temperature: -40°C to +85°C ( if temperature too high , please enhance heat dissipation)
- Operating Frequency : 150KHz
- Conversion efficiency : up to 95% ( affected by input voltage, output volage, current and dropout voltage )
- Operating Ripple: about 100mV
- Load Regulation rate: about 0.2%
- Voltage regulation rate: about 2%
- Overcurrent protection : Yes ( input exceeds 17A, automatically reduces the output voltage , maybe have errors)
- Short-circuit protection: Yes (input with 20A fuse) double circuit protection, more safe.
- Input Reverse Polarity Protection: No , ( if necessary , input add one diode in series)
- Output prevent backflow : Yes, no need to add prevent backflow diode for charging .
- Installation: two 3mm screws
- Wiring: terminals, no welding.
- Size: 76mm(L) * 60mm(W) * 56mm(H, the height of the heatsink is included)
- Net weight: 205 g
Applications:
- DIY a regulated power supply, only 12V input, output 12-80V adjustable.
- Power supply for your electronic device , according to your system can set the output voltage value .
- As a vehicle power supply, power supply for your laptop/PDA etc.
- DIY a laptop mobile power supply, with 12V high capacity lithium battery pack, travel no worry.
- Solar panels regulator.
- Charge for the battery.
- Drive high-power LED.
- Constant current range: 0.1-12A
-
-
Funktion |
DC/DC |
Manufacturer |
No Brand |
Supply voltage |
8...60 VDC |
Effekt, Kontinuerlig upp till. |
...600 W |
Output current |
0...12 A |
Anslutning primärsida |
Skruvanslutning |
Output connector type |
Skruvanslutning |
Utförande |
För inbyggnad |
Information |
Produkten är ingen färdig anordning, utan endast en komponent |